Raytheon Super Type Marble Alcohol White Tile Adhesive it is a special mortar product made of selected natural mineral raw materials and modified polymers, with a white color, especially suitable for paving marble natural decorative materials. The advantage of non-bleeding products can present 100% of the original style of stone. The product has strong adhesion and convenient construction. Through the French indoor air environment test A + level standard, green safety, tile worry-free

1. suitable for concrete, cement plaster, concrete slab, plastering brick surface, cement-based waterproof coating and other grass-roots
2. Suitable for indoor wall paving size ≤ 400*800mm ceramic tiles, glazed tiles, marble and other natural stone
3. Indoor and outdoor, wall and ground are applicable

1. [Water ratio]

the mixing ratio of water is powder: clear water = 20kg:4.2-5.4kg

2. [Mixing method]

pour an appropriate proportion of water into the mixing bucket, and then pour the powder into the water and use an electric mixer to stir evenly, that is, the mixing method of adding water first and then pouring the material. Note: If the mixing method of pouring the material first and then adding water is adopted, it is easy to cause the ceramic tile adhesive mass to not be stirred, which not only affects the subsequent construction, but also causes the material performance to decline.

3. [Stirring time]

Use a mixer to fully stir until there is no raw powder, place for 3-5 minutes, and then stir for 15-30 seconds to use, mixing good tile glue should be used up within 2 hours

4. [recommend construction]

recommend use double-sided scraping method thin paste construction

5. [Construction method]

with a spatula will tile glue force thin coated on a stable base, and then a thick batch of a layer of tile glue, and with a suitable tooth-shaped spatula combing tile glue layer, each coating area ≤ 1m², and then knead the tiles with a thin batch of tile glue on the back on the undried and combed tile glue layer. Before tiling, check whether the adhesive layer has been dried on the surface. If it has not been dried on the surface, tiling can be applied again. The depth of the spatula teeth should consider the flatness of the base layer and the degree of convexity and concavity on the back of the tile.

6. [Special attention]

apply tile glue to the base layer of the tile and comb it, apply tile glue to the back of the tile, then stick the tile on the carded tile glue layer and knead it properly. In order to ensure the construction quality, the construction personnel should open the tiles that have been pasted from time to time to ensure that the base surface on the back of the tiles is all glued with tile glue.

7. [Reference Dosage]

Per square meter 1mm thickness of dosage is about 1.5kg; The specific situation depends on the base surface flatness and tile size.

1. The product should be used by adding water in accordance with the reference ratio. After adding water and stirring, it should be used up within 2 hours. It is strictly prohibited to add any other materials, such as cement, sand, fine powder, lightweight materials, etc
2. This product is made from natural minerals as raw materials. Color differences between batches are normal phenomena and do not affect normal use
3. Metal or metal-containing mirror mosaics and cement-based products of this type may cause corrosion. Local tests must be conducted by yourself before use
4. The grid cloth on the back of the stone is mostly made of resin-based materials, which cannot ensure its compatibility and adhesion with cement-based products. It is necessary to remove the grid cloth completely first
5. The release agent on the back of the tiles must be cleaned thoroughly
6. Never mix damp or clumped dry powder of the adhesive with water before use
7. The construction temperature should be between 5 and 35℃. Construction should be avoided as much as possible in rainy, high-temperature, strong wind, severe cold and frost weather. If construction needs to be carried out on rainy days, proper shielding and protective measures should be taken, and it is necessary to ensure that the construction area is not wet by rain within 24 hours after construction
8. It is recommended to use a toothed scraper tool to lay tiles at an Angle of about 60 degrees to the inner side of the base layer. The thin laying process of applying mortar on both the wall and the back of the tiles should be adopted, and the standard requirement is ≥95%
9. When laying tiles, the thickness of the adhesive mortar should be between 3 and 10mm
10. When tiling indoors, there must be a gap of no less than 2mm between each tile
11. After the bricklaying is completed, the next step of grouting can only be carried out after the mortar has completely dried and solidified (≥24 hours)